Search Results

As an effective method to solve the global warming and the energy crisis, the research has been carried out for the adaptability of plant oil as an alternative fuel for Diesel engine. But there are the problems of engine performance and exhaust emissions owing to the high viscosity and low volatility, when the plant oil is used as a fuel. In order to eliminate these problems, spray characteristics of the DME (Dimethyl ether) blended plant oil has been examined by using the image processing based on the shadowgraph methodology. Results show that the optimum mixing ratio of the blend is about 50:50 (by weight %). Thereafter, experiments have been conducted with a DI Diesel engine using the DME blended plant oil, and compared the exhaust emissions with Diesel, DME and transesterified fuel operation. From the results, it can be concluded that the combustion characteristics of DME blended plant oil are comparable to Diesel fuel.

This research investigated the performance and emissions of a direct injection (DI) Diesel engine operated on 100% butane liquid petroleum gas (LPG). The LPG has a low cetane number, therefore di-tertiary-butyl peroxide (DTBP) and aliphatic hydrocarbon (AHC) were added to the LPG (100% butane) to enhance cetane number. With the cetane improver, stable Diesel engine operation over a wide range of the engine loads was possible. By changing the concentration of DTBP and AHC several different LPG blended fuels were obtained. In-cylinder visualization was also used in this research to check the combustion behavior. LPG and only AHC blended fuel showed NOX emission increased compared to Diesel fuel operation. Experimental result showed that the thermal efficiency of LPG powered Diesel engine was comparable to Diesel fuel operation. Exhaust emissions measurements showed that NOX and smoke could be considerably reduced with the blend of LPG, DTBP and AHC.

Detailed chemical kinetic model of hydrogen peroxide (H2O2) into diesel exhaust gas has been executed to investigate its effect on the removal of nitric oxide(NO) by changing exhaust gas temperature and H2O2 addition amount. Flux analysis has also been done to clarify which reaction mainly affects NO-to-NO2 conversion. From the results of this study, it is shown that the optimal temperature condition to maximize the removal of NO exists near at 500K for OH addition condition, while that for H2O2 addition exists near at 800K. It is also shown that temperature window for the removal of NO becomes widened as the initial temperature of the exhaust gas increases, and NO-to-NO2 conversion rate decreases in proportion to the concentration of hydrocarbon(HC), although that of the total NOx remains the same level regardless of HC concentration. Finally, it is shown that HO2 + NO → NO2 + OH is mainly responsible for NO-to-NO2 conversion.

Development of LPG SI and CI engines for heavy duty vehicles has been carried out. In order to measure the performance and emissions of an LPG lean burn SI engine, the piston cavity, swirl ratio, and propane-butane fuel ratio were varied and tested. Compared to the bathtub and dog dish cavities, the nebula type cavity showed the best performance in terms of cyclic variation and combustion duration. High swirl improved combustion by achieving a high thermal efficiency and low NOx emissions. A feasibility study of an LPG DI diesel engine also has been carried out to study the effectiveness of the selected cetane enhancing additives:Di-tertiary-butyl peroxide (DTBP). When more than 5 wt% DTBP was added to the base fuel, stable engine operation over a wide range of engine loads was possible. The thermal efficiency of LPG fueled operation was found to be comparable to diesel fuel operation at DTBP levels over 5 wt%.

The oxidation mechanism of DTBP (Di-tertiary-butyl peroxide) and its role in butane oxidation have been investigated, as it pertains to the development of an LPG DI diesel engine. Ignition delay contours were analyzed to investigate the role of DTBP (ϕ≈0.2 to the total oxygen) in butane oxidation. At higher pressure and lower temperature regions, it was apparent that the addition of DTBP significantly enhances the ignition delay of butane, whereas at lower pressures and higher temperatures, this effect diminishes. Results of this study showed that the role of DTBP to enhance the ignition delay of the base fuel is through rapid heat release, rather than by radicals produced by decomposition during the base fuel ignition delay. Formaldehyde is a principal species involved in reactions for heat release in the higher pressure lower temperature region, comparable to diesel engine operating conditions.

To find more effective lean mixture preparation methods for smokeless and low NOx combustion, a numerical study of the effects of in-cylinder flow field before injection on mixture formation in a premixed compression ignition engine was conducted. Premixed compression ignition combustion is a very attractive method to reduce both NOx and soot emissions, but it still has some problems, such as high HC and CO emissions. In case of early direct injection, it is important to avoid wall wetting by spray impingement, which can cause higher HC and CO emissions. Since it is not easy to examine the effects of initial flow and injection parameters on mixture formation over the wide range by practical engine tests, a computer program named “GTT (Generalized Tank and Tube)” code was used to simulate the in-cylinder phenomena before autoignition.

A feasibility study of an LPG DI diesel engine has been carried out to study the effectiveness of two selected cetane enhancing additives: Di-tertiary-butyl peroxide (DTBP) and 2-Ethylhexyl nitrate (EHN). When more than either 5 wt% DTBP or 3.5 wt% 2EHN was added to the base fuel (100 % butane), stable engine operation over a wide range of engine loads was possible (BMEPs of 0.03 to 0.60 MPa). The thermal efficiency of LPG fueled operation was found to be comparable to diesel fuel operation at DTBP levels over 5 wt%. Exhaust emissions measurements showed that NOx and smoke levels can be significantly reduced using the LPG+DTBP fuel blend compared to a light diesel fuel at the same experimental conditions. Correlations were derived for the measured ignition delay, BMEP, and either DTBP concentration or cetane number. When propane was added to a butane base fuel, the ignition delay became longer.

Band spectrum images for CH, OH and CHO were taken in a heavy duty type LPG lean-burn SI engine, to investigate the combustion process as it pertains to the pollutant formation process in the post flame region. Full spectra and band spectrum flame images were observed with a bottom view single cylinder research engine and two high speed cameras. NOx emissions were also measured for excess air ratios ranging from 1.0 to 1.6. A thermodynamic model, including the detailed chemical kinetic mechanism for LPG and NOx formation reactions, was developed to predict the major reaction species in the post flame region, and NOx emissions during the combustion process. The model qualitatively described the flame images for each band spectrum and could predict the measured NOx emissions very well.

Performance and emissions of an LPG lean burn engine for heavy duty vehicles were measured. The piston cavity, swirl ratio, propane - butane fuel ratio, and EGR were varied to investigate their effects on combustion, and thus engine performance. Three piston cavities were tested: a circular flat-bottomed cavity with sloped walls (called the “bathtub” cavity), a round bottomed cavity (called the “dog dish” cavity), and a special high-turbulence cavity (called the “nebula” cavity). Compared to the bathtub and dog dish cavities, the nebula type cavity showed the best performance in terms of cyclic variation and combustion duration. It was capable of maintaining leaner combustion, thus resulting in the lowest NOx emissions. High swirl improved combustion by achieving a high thermal efficiency and low NOx emissions. In general, as the propane composition increased, cyclic variation fell, NOx emissions increased, and thermal efficiency was improved.

Using an extended bottom view piston having a quartz window, flame propagation observation and flame contour analysis were carried out to investigate the combustion characteristics of a heavy-duty type LPG lean burn engine. The swirl ratio and piston cavity configuration were varied to investigate their effects on combustion and engine performance. Gradual reduction of NOx but increased hydrocarbon emissions were measured for leaner mixtures compared to the stoichiometric operation. High swirl apparently accelerated the initial flame kernel development, as evidenced by a shorter crank angle interval from the spark ignition to the maximum cylinder pressure. The ‘D’ type cavity, with an increased squish area located below the intake valve, was shown to have the shortest burn duration among the piston cavities tested. The experimental flame propagation observation procedure was shown to be useful for the study of the combustion process in engines.

In this study, a piezo disk was used to generate a cloud of n-decane fuel drops, which were mixed with air, then carried into a combustion chamber and ignited by a platinum wire. Microgravity data obtained at the Japan Microgravity Center (JAMIC) were compared to normal gravity data, all at 1Atm pressure and 20+/-1°C initial temperature. Under normal gravity the lean limit was found to be 7.6x106/mm3 (Φ = 1.0), and from this point the flame front speed steadily increased from 20cm/s up to a maximum flame front speed of 210cm/s at a fuel drop density of about 14x106/mm3 (Φ = 1.85). Microgravity data showed a much richer lean limit - about 14.5x106/mm3 (Φ = 1.9), and the flame front speed did not gradually rise to a peak value. Instead, the measurements indicated a peak value of about 250cm/s, with a steep increase followed by a gradual decrease at richer fuel air ratios. A cellular flame structure appeared, and the cell size decreased as the mixture density increased.

Flame propagation at elevated pressures for propane, butane and autogas (20% propane and 80% butane by mass) were investigated. Flame arrival time was measured using ionization probes installed along the wall of a cylindrical combustion chamber. Flame radius was also measured using a laser schlieren technique. Results showed that the flame front speed decreased with increasing initial pressure, and the initial pressure effect on maximum flame front speed was correlated by the relationship Sf = 175·pi-0.15 (for Φ=1.0). Characteristics of flame front speed between propane, butane and autogas were very similar, whereas at fuel-rich conditions flame front speed of butane and autogas were higher than that of propane. A thermodynamic model to predict flame radius and speed as a function of time was derived and tested using measured pressure-time curves.

The combustion mechanism of a fuel droplet cloud was studied by numerical simulation. We investigated how the flame front speed and combustion products changed depending on the equivalence ratio and initial temperature. Modeling was performed using the KIVA-III software package, a three dimensional analysis software used mainly for internal combustion engine applications. The computational domain was a horizontal 1x1x100 cell sector of a spherical combustion chamber and the fuel was n-decane. Results showed that when all the fuel droplets were assumed to have evaporated, the flame front speed increased from 28 cm/s to 152 cm/s as the equivalence ratio increased. The maximum flame front speed was reached at ϕ=1.1, beyond which it decreased (at richer overall equivalence ratios). With a constant equivalence ratio, the flame front speed decreased near the outside region, because the unburned gas was compressed by the expanding burned gas.

The effects of upstream conditions, such as nozzle and entrance shapes, on external flow characteristics continue to challenge fuel injection modeling efforts, particularly in the case of high-pressure diesel sprays. In this research, flow details were investigated both experimentally and numerically in a fuel injector nozzle orifice using an integrated approach. Calculations using the SIMPLE algorithm were first performed for the scaled-up experimental nozzles with various length to diameter ratios (L/d). Measurements of internal flow velocities for these nozzles were made by laser Doppler velocimetry in order to verify the computational results. Mean and fluctuating velocities and discharge coefficients were obtained at various Reynolds numbers. The mean turbulence intensity and turbulent kinetic energy for a sharp inlet nozzle were generally higher than for a round inlet nozzle, except for the near-wall region beginning at about one nozzle diameter from the entrance.

This paper deals with the process regarding how dehydrogenation of soot particles takes place. The measured carbon/hydrogen ratios plotted against mean-diameter of soots fall on a straight line passing through the origin. It is shown that in the course of soot particle growth CM ratio increases linearly with the particle diameter: D. This is an indication of the fact that the number of carbon grows in proportion to D3, whereas that of hydrogen is proportional to D2. It is there by concluded that hydrogen sit only on surface of soot particles.

The authors tried to use LP gas, mainly butane, as the main fuel of diesel engines to reduce soot and to maintain high thermal efficiency. LP gas was injected in the direction of the intake valve directly as a spray to prevent knocking and to preserve high charging efficiency. The newly developed electronic fuel injection provided accurate fuel control and injection timing. As a result, the dual-fuel operation produced high thermal efficiency almost identical to that of diesel engines. Soot in engine exhaust was almost negligible. Three quarters of maximum output was obtained with butane, and only small amount of gas oil for idling, in spite of an high compression ratio of 17 for gas engines. Increasing the proportion of gas oil resulted in maximum output from a diesel engine and almost no soot output.

This paper presents the result of a theoretical study on the effects of particle size distribution on the soot particle measurement method. The principal equations are rear-ranged into a concise form, and a wide variation of size distribution functions are introduced to calculate the effects. It was found that the mean extinction coefficient is very weakly dependent on the shape of size distribution functions and can be approximated to that for the Sauter mean diameter with insignificant error. The volumetric density of soot particles can be obtained by light transmittance measurement on a single wavelength, and this is affected only by the estimated value for the Sauter mean diameter. The error due to the estimation is under 5%. On the other hand, it was found that the light transmittance measurement is insufficient to obtain size distribution or the Sauter mean diameter of soot particles.

Remarkable progress has been made in recent years on pressure measuring techniques and apparatuses, yet they seem not necessarily successful in achieving accurate pressure diagrams at the high frequency range. The primary cause of difficulty lies in the occurrence of undesirable vibrations in the connecting passages which diminishes the accuracy of pressure diagrams. In order to prevent such vibration, the authors have attempted to increase the natural frequency in the connecting passages by enclosing heat resisting silicon oil, to analyse the frequency characteristics of the passages, and to ensure the propriety of the analysis through comparison with experiments. As a result, it is proved that the natural frequency of the silicon oil enclosed passage increases twice as high as that of the passage filled with working gas.

The authors designed and produced a new dual fuel injector that allows two different kinds of fuel to be injected. This injector contains both a throttle type nozzle and a hole type which are located coaxially. The injection timing as well as the fuel quantity can be controlled individually. The running test using two lines of gas oil brought a good reduction of NOx and exhaust smoke. The experiment using gas oil and alcohol also brought a satisfactory reduction of exhaust emission.